AUTOGLYM
Autoglym Polar Blaster Snow Foam Gun, Polar Blast, Polar Wash and Polar Seal Starter Kit
Autoglym Polar Blaster Snow Foam Gun, Polar Blast, Polar Wash and Polar Seal Starter Kit
Couldn't load pickup availability
This kit contains:
- Polar Blaster Snow Foam Gun, the connector is compatible with the Karcher K-Series of pressure washers, other connectors are available.
- Polar Blast 2.5 litre
- Polar Wash 2.5 litre
- Polar Seal 1 litre
- 1 x Autoglym InstaDry cloth
How To Use:
setup your Polar Blaster Snow Foam Gun
- Designed to work with all Polar Series products
- Adjustable spray pattern
- Quick, fun and safe to use
Then add
- Before you start, check that the bodywork and wheels are cool to the touch and out of direct sunlight.
- Polar Blast can be uséd at various dilutions depending on the density of foam desired. A good starting point is a 100ml product to 500ml water in your foaming bottle. Adjust foam gun settings as required to increase or reduce foam.
- Spray Polar Blast onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass and wheels.
- Leave Polar Blast time to dwell and loosen dirt for up to 10 minutes, although do not allow it to dry on.
- Finally, rinse thoroughly from the bottom up.
Polar Wash
- Before you start, check that the bodywork and wheels are cool to the touch and out of direct sunlight.
- We recommend a pre-wash with Polar Blast to gently loosen dirt. If not, rinse first with water to loosen heavy contamination.
- Polar Wash can be uséd at various dilutions depending on the density of foam desired. However, we would not recommend using a dilution stronger than 50:50. Adjust foam gun settings as required to increase or reduce foam. 250ml of the mixed solution should be enough to cover an average-sized car.
- Spray Polar Wash onto the vehicle, starting at the bottom, ensuring all exterior surfaces are covered, including glass and wheels.
- The cleaner will begin to loosen dirt on all surfaces. For the most thorough clean we recommend agitating the foam with a sponge or wash mitt.
- Rinse thoroughly from the bottom up and dry.
Polar Wash is not suitable for use on soft-top convertibles.
Top Tip? Follow with Polar Seal for a protective, hydrophobic coating
Polar Seal
- Before you start, check that the bodywork and wheels are cool to the touch and out of direct sunlight.
- We recommend starting with a snow foam like Polar Blast to gently loosen dirt, and follow with Polar Wash to remove any dirt or contamination on your paintwork.
- Only a small amount of Polar Seal is required. Pour no more than 40ml (four capfuls) into your foam bottle and then add at least 200ml of water. This should be all the finished solution required to cover your vehicle. There is no benefit in using any more than 40ml as over-application can compromise the finish.
- Spray Polar Seal onto the clean, wet vehicle, ensuring all exterior surfaces are covered, although avoid direct application to the windscreen.
- Thoroughly rinse and dry your car to reveal a high-gloss finish that is protected with a hydrophobic coating. The car must be dried with a cloth and not allowed to air dry as water spotting may occur.
- Use Autoglym Fast Glass to clean the windscreen and wiper blades to ensure no smearing occurs.
We do not recommend applying more than once a month.
Polar Seal is not suitable for use on soft-top convertibles.
Do not store diluted product. Please rinse foam bottle and pressure washer lance after use.
Top Tip? For the optimum finish, dry with the Autoglym InstaDry cloth
![Autoglym Polar Blaster Snow Foam Gun, Polar Blast, Polar Wash and Polar Seal Starter Kit - cccampers.myshopify.com](http://cccampers.myshopify.com/cdn/shop/products/AutoglymPolarSeriesBundle-PolarBlast_Wash_Seal_Instadrycloth_Blaster.jpg?v=1607962359&width=1445)